How WiFi Works PowerPoint Presentation

Slide 1 -

How WiFi Works LUCID Summer Workshop August 3, 2004

Slide 2 -

Outline for Today Last we learned how to setup a WiFi network. This time we will learn about the protocols that enable these networks. Towards the end, we will discuss WiMax, an emerging fixed wireless technology which may impact Susquehanna.

Slide 3 -

802.11 Operating Frequency The 802.11 suite has been developed to enable wireless local area networking in either the 2.4 GHz or 5.2 GHz frequency bands. Specifically, the frequencies used by 802.11 fall in the unlicensed bands, these are frequency bands which anyone can use for radio communication (without a license) as long as their radio waves do not radiate too much power. The exact frequencies used (and how they are used) depends on whether the system follows 802.11b, 802.11a, or 802.11g.

Slide 4 -

802.11b The 802.11b standard defines a total of 14 frequency channels. FCC allows channels 1 through 11 within the U.S. Most of Europe can use channels 1 through 13. In Japan, only 1 choice: channel 14. Channel represents a center frequency. Only 5 MHz separation between center frequencies of channels. 2 1 3 4 5 6 7 8 9 10 11 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 Channel Center Frequency (GHz) 5 MHz

Slide 5 -

802.11b (Cont’d) Any 802.11b signal occupies approximately 30 MHz. Thus, 802.11b signal overlaps with several adjacent channel frequencies. Only three channels (channels 1, 6, and 11 for the U.S.) that can be used without causing interference between access points. Any given area can therefore support at most 3 access points (operating on different channels) at once. Equivalently, it can at most support three local ad-hoc connections.

Slide 6 -

802.11b (Cont’d) 2 1 3 Access Point Neighboring AP’s use different channels to reduce interference. “Reuse cluster” size is equal to 3.

Slide 7 -

802.11b (Cont’d) Ideally, 802.11b supports wireless connections between an access point and a wireless device at four possible data rates: 1 Mbps, 2 Mbps, 5.5 Mbps, and 11 Mbps. Specifically, as terminal travels farther from its AP, the connection will remain intact but connection speed decreases (falls back).

Slide 8 -

802.11b (Cont’d) 11 Mbps 5.5 Mbps 2 Mbps

Slide 9 -

802.11b Spread Spectrum When a 802.11b radio is operating at 1 Mbps and wishes to transmit a bit 1, it has to do so in 0.000001 seconds. The way 802.11b does is this by actually transmitting a fixed sequence of 11 shorter bits (01001000111) to represent a single bit “1”. These 11 “shorter bits” (which represent one information bit) are sent in 1/11 the time, i.e., 0.0000000909 seconds. These shorter bits are called “chips.”

Slide 10 -

802.11b Spread Spectrum (Cont’d) When the radio wishes to transmit a 0 information bit, it uses the 0.000001 seconds to transmit a different fixed sequence of chips, 01001000111. The chip sequence used for “1” is the complement of the chip sequence used for sending a “0”. Why is this done?

Slide 11 -

802.11b Spread Spectrum Assume the original signal (the information stream of 1’s and 0’s) occupies a frequency bandwidth of W Hz. When we use N chips to transmit 1 bit, the bandwidth of the resulting signal now occupies NW Hz. The new signal has a larger spectrum, i.e., the information signal of bandwidth W has been spread to a bandwidth of NW. For this reason, this process is called spread spectrum.

Slide 12 -

Spread Spectrum W Hz Frequency representation of transmitted signal, before and after spreading. NW Hz Before After Both signals contain the same information. The second signal uses less power/Hz (height is less). This helps meet FCC mandates in unlicensed bands.

Slide 13 -

802.11b (Cont’d) The above procedure is used to get 1 Mbps. What about the higher data rates? This is achieved by using more complex modulation schemes and/or changing the chip sequence. Recall modulation scheme is the scheme used to encode a bit stream into high-frequency sine waves, i.e., radio waves.

Slide 14 -

802.11a 802.11a specification operates at radio frequencies between 5.15 and 5.825 GHz, i.e. 802.11a utilizes 300 MHz bandwidth in Unlicensed National Information Infrastructure (U-NII) band. The FCC has divided total 300 MHz in this band into three distinct 100 MHz bands: low, middle, and high, each with different legal maximum power. Band Channel Max Power High band 5.725-5.825 GHz 9-12 1000 mW Middle band 5.25-5.35 GHz 5-8 250 mW Low band 5.15-5.25 GHz 1-4 50 mW

Slide 15 -

802.11a (Cont’d) Because of high power output, high band used for building-to-building products. Lower two bands suitable for in-building wireless products. In 802.11a, radio signals are generated using a method called Orthogonal Frequency Division Multiplexing (OFDM). OFDM is defined over the lower two bands (low and middle).

Slide 16 -

802.11a (Cont’d) The low and middle bands have a total of 200 MHz of frequency. This 200 MHz supports 8 non-overlapping channels. Each channel is split in 52 bands, each approximately 300 kHz wide. Each of these smaller bands is called a subcarrier in OFDM terminology. In OFDM, a transmitter can select some number of subcarriers to transmit a signal over.

Slide 17 -

802.11a (Cont’d) Depending on the number of subcarriers chosen, the transmitter can achieve transmission rates of 6, 9, 12,18, 24, 36, 48, or 54 Mbps. Since there are eight non-overlapping channels, 802.11a can support 8 different access-point to wireless device links in a given location. Or equivalently, it can support at most 8 ad hoc connections simultaneously. This is an improvement over 802.11b, where only 3 could be supported.

Slide 18 -

802.11a (Cont’d) 1 2 3 Access Point 4 5 6 7 8 Neighboring AP’s use different channels to reduce interference. “Reuse cluster” size is equal to 8.

Slide 19 -

802.11a (Cont’d) The various data rates are supported in 802.11a by varying the number of subcarriers, the modulation scheme, etc. 802.11a (like 11b) has a rate fall back mechanism, i.e., as the distance between the transmitter and receiver increases, the supported data rate decreases.

Slide 20 -

802.11a (Cont’d) 54 Mbps 48 Mbps 36 Mbps 24 Mbps 12 Mbps 2 Mbps 5.5 Mbps 11 Mbps 802.11a 802.11b

Slide 21 -

802.11g 802.11g offers throughput of 802.11a with backward compatibility of 802.11b. 802.11g operates over 3 non-overlapping channels. 802.11g operates in 2.4 GHz band but it delivers data rates from 6 Mbps to 54 Mbps. 802.11g also uses OFDM but supports spread-spectrum capabilities if any one component of the system has older equipment, i.e., 802.11b equipment.

Slide 22 -

802.11g Once again, 802.11g’s "backward compatibility" with 802.11b means that when a mobile 802.11b device joins an 802.11g access point, all connections on that access point slow down to 802.11b speeds. So both 11a and 11g offer the same data rates. Which is better?

Slide 23 -

Comparing 11a and 11g 802.11a operates in underused 5 GHz band; 802.11g operates in heavily used 2.4 GHz band. 11g systems experience interference from other 2.4 GHz devices such as cordless phones, microwave ovens, satellites, etc. Both 802.11a and 802.11g offers up to 54Mbps speeds in the lab.

Slide 24 -

Comparing 11a and 11g (Cont’d) In the field, 802.11a delivers about 20Mbps. 802.11b's 11Mpbs theoretical speed is more often 4Mbps in practice. The realistic data rates quoted for 802.11g thus far range from 6 Mbps to 20 Mbps. 11g has to contend with more interference in the 2.4 GHz range as compared to 11a in the 5 GHz band.

Slide 25 -

Comparing 11a and 11g (Cont’d) Higher number of channels in 11a allows more flexibility in avoiding interference. Range will depend on antenna gain, transmit power applied to the antenna, the receive sensitivity of the radio card and the obstacles between path ends. 802.11a has range 150-300 ft in practical scenarios. 11g has range comparable to 11b (approximately 1000 ft). 11a range is smaller than 11b and 11g. This is because 11a operates at a much higher frequency band.

Slide 26 -

Comparing 11a and 11g (Cont’d) Generally, 802.11a is the most expensive of the three options. 802.11b is the cheapest and most popular WLAN option. 802.11g is more expensive than 11b but cheaper than 11a. Because of its smaller range, 11a requires more Access Points to a region, thereby increasing cost.

Slide 27 -

What does a typical 802.11 Packet look like? Typical 802.11 packet: Preamble is used to synchronize the receiver, so it can tell when the packet starts. It contains 96 bits. PLCP (Physical Layer Convergence Procedure) indicates how many bytes in data portion, what is the data rate of the transmission, etc. This portion contains about 192 bits. Preamble PLCP Header Data CRC

Slide 28 -

802.11 Packet (Cont’d) Data is the actual data transmitted by the source. This contains source/destination addresses, the information conveyed between the two, whether WEP is on or not, etc. The amount of data bits can vary. ~200 bits to ~18000 bits. CRC is the cyclic redundancy check, which is way of checking if there was an error in the received sequence of bits. This is usually 32 bits long. Preamble PLCP Header Data CRC

Slide 29 -

How are Multiple Transmitters Supported? Recall the method for supporting multiple transmitter is called the multiple access method. In 802.11 systems, only one user is allowed to communicate with a receiver at a time (cannot use another frequency channel support a second or third additional user). The way the one user is selected depends on the carrier sense multiple access with collision avoidance (CSMA/CA) random access method.

Slide 30 -

CSMA To help illustrate the operation of CSMA, we will use an analogy of a dinner table conversation. Let’s represent our wireless medium as a dinner table, and let several people engaged in polite conversation at the table represent the wireless nodes.

Slide 31 -

CSMA (Cont’d) The term multiple access covers what we already discussed above: When one wireless device transmits, all other devices using the wireless medium hear the transmission, just as when one person at the table talks, everyone present is able to hear him or her. Now let's imagine that you are at the table and you have something you would like to say. At the moment, however, I am talking.

Slide 32 -

CSMA (Cont’d) Since this is a polite conversation, rather than immediately speak up and interrupt, you would wait until I finished talking before making your statement. This is the same concept described in the CSMA protocol as carrier sense. Before a station transmits, it "listens" to the medium to determine if another station is transmitting. If the medium is quiet, the station recognizes that this is an appropriate time to transmit.

Slide 33 -

CSMA/CA Carrier-sense multiple access gives us a good start in regulating our conversation, but there is one scenario we still need to address. Let’s go back to our dinner table analogy and imagine that there is a momentary lull in the conversation. You and I both have something we would like to add, and we both "sense the carrier" based on the silence, so we begin speaking at approximately the same time. In 802.11 terminology, a collision occurs when we both spoke at once.

Slide 34 -

CSMA/CA (Cont’d) The collision will result in an undecipherable message to the intended receivers (listeners). What we need is a polite contention method to get access to the medium; this is the collision avoidance part of CSMA/CA. 802.11 has come up with two ways to deal with this kind of collision. One uses a two-way handshake when initiating a transmission. The other uses a four-way handshake.

Slide 35 -

2 Way Handshake Node with packet to send monitors channel. If channel idle for specified time interval called DIFS, then node transmits. If channel busy, then node continues to monitor until channel idle for DIFS. At this point, terminal backs-off for random time (collision avoidance) and attempts transmitting after waiting this random amount of time.

Slide 36 -

2 Way Handshake If the node does not back-off the random time, then it will definitely collide with another node that has something to send. Reason for random back-off time is that if I choose a random time and you choose a random time, the probability that we choose the same random time is slim. This way we both back-off transmitting and will therefore will probably not interfere with each other when we are ready to transmit.

Slide 37 -

2 Way Handshake (Cont’d) First way of the 2 way handshake was for the transmitter to send its information packet to the destination node, after following the collision avoidance method described above. If the packet reaches the destination without problems, the destination sends a short packet over the wireless medium acknowledging the correct reception. This packet is typically called an ACK packet. ACK is the second way of the 2 way handshake.

Slide 38 -

4 Way Handshake “Listen before you talk” If medium is busy, node backs-off for a random amount of time after waiting DIFS, just as before. But now, instead of packet, sends a short message: Ready to Send (RTS). This message is basically attempting to inform others that “I have something to send.”

Slide 39 -

4 Way Handshake (Cont’d) RTS contains destination address and duration of message. RTS tells everyone else to back-off for the duration. If RTS reaches the destination okay (no one else collides with this message), the destination sends a Clear to Send (CTS) message after waiting a prescribed amount of time, called SIFS.

Slide 40 -

4 Way Handshake (Cont’d) After getting the CTS, the original transmitter sends the information packet to its destination. In these systems, the transmitter cannot detect collisions. The receiver uses the CRC to determine if the packet reached correctly. If it does then, it sends out an ACK packet. If the information packet not ACKed, then the source starts again and tries to retransmit the packet.

Slide 41 -

4 Way Handshake (Cont’d) Access Point Laptop RTS CTS Data ACK

Slide 42 -

WiMax

Slide 43 -

What is WiMax? WiMax is a radio technology that promises to deliver two-way Internet access at speeds of up to 75 Mbps at long range. Its backers claim that WiMax can transmit data up to 30 miles between broadcast towers and can blanket areas more than a mile in radius with bandwidth that exceeds current DSL and cable broadband capabilities. So, some believe that it could slash the cost of bringing broadband to remote areas.

Slide 44 -

WiMax (Cont’d) WiMax, short for Worldwide Interoperability for Microwave Access, is the latest of the wireless "last mile" broadband technologies. ISP see WiMax as a means of connecting rural or remote areas with broadband service, something that would be technically, physically or economically difficult to do by burying wire for DSL or cable connections. Laying wires is especially difficult in hilly areas like Susquehanna.

Slide 45 -

Benefits over Satellite In rural areas, the real competition to WiMax would be satellite data services. The benefit that WiMax offers over satellite is that satellite offers limited uplink bandwidth (upload data rates are not as high as download data rates). Further, satellite suffers with high latency.

Slide 46 -

WiMax (Cont’d) In congested cities, WiMax products could shift traffic to help relieve heavy demand on broadband networks. WiMax will work with other shorter-range wireless standards, including Wi-Fi, which has taken off as an easy way to provide Internet access throughout a home or business. Eventually, advocates hope to see the standard evolve into a mobile wireless Internet service similar to cellular data technologies. It may not ever be as wide-area as cellular but will offer higher data rates.

Slide 47 -

WiMax Protocols The protocols that govern WiMax have been standardized. They are collectively referred to as 802.16. Like Wi-Fi = 802.11, WiMax = 802.16. Overall vision for 802.16 is that carriers (e.g., ISP) would set up base stations connected to a public (wired) network. This is like cellular. Each base station would support hundreds of fixed subscriber stations. Fixed means that subscriber stations do not move. Plans to expand the standard to include mobile stations is in the working.

Slide 48 -

More on WiMax Base stations will use the 802.16 protocols to dynamically allocated uplink/downlink bandwidth to subscriber stations based on their demand. 802.16 has been developed for several frequency bands (various licensed frequencies in 10-66 GHz, also licensed and unlicensed frequencies in 2-11 GHz). In the unlicensed bands, 802.16 can be used as a backhaul for wi-fi systems or a longer-range alternative, i.e., replacing hotspots with hotzones.

Slide 49 -

Some Technical Specs on WiMax The radio technology is based on OFDM. 802.16 standards incorporate use of adaptive antenna arrays, which can be used to create dynamic beams in desired directions. Standards offer option for a mesh mode network topology.

Slide 50 -

Mesh Networking in WiMax When a subscriber unit is not in line of sight with the base station (does not have a good signal strength), then it may be able to make a peer-to-peer connection to a neighbor, i.e., hop to a neighbor’s subscriber unit. The neighbor’s unit may be in line of sight with the base station, in which case this neighbor would serve as a relay station (a repeater). If the neighbor’s unit is not in line-of-sight then another hop can be made.

Slide 51 -

Mesh Mode Trunk (Wired) Network Trunk Residential Business

Slide 52 -

WiMax Costs Analysts estimate that subscriber stations for home access will initially cost up to $300. Base stations will cost as little as $5,000 but will reach $100,000, depending on their range. Each base station may be able to support up to 60 T1 class subscriber lines. In some cases, consumers would lease subscriber stations from carriers the way they do with cable set-top boxes as part of their service plans.

Slide 53 -

WiMax Predictions Base stations will be able to connect to other base stations within a range of up to 30 miles with data transfer speeds of up to 75 megabits per second. Subscriber stations, the set-top box-like devices, will connect to base stations with ranges of up to three miles and transfer speeds of up to 15 megabits per second. WiMax T1 class lines may cost 10% of wired T1 costs. Products will start being available 2005-2006.

Slide 54 -

LUCID Summary The last few days, we have reviewed how several important wireless technology work. Cellular Telephony GPS WiFi WiMax All these technologies offer opportunities to improve the communication capabilities in numerous ways and at various scales.

Slide 55 -

LUCID Summary (Cont’d) We hope you will consider how these technologies can impact your life and the lives of those around you. We would also appreciate any and all feedback you can give us on this workshop (skishore@lehigh.edu). Finally, we would like to encourage all participants, particularly the students, to come visit Lehigh University. Thanks!